Product Overview
Banks Power Monster-Ram® Intake and Killer Grid Heater Upgrade for 2013–2018 Dodge Ram 6.7L Cummins
The Banks Power Monster-Ram® is a direct-fit intake elbow replacement designed for compatible 2013–2018 Dodge Ram 2500 and Ram 3500 trucks equipped with the 6.7L Cummins diesel engine, including dual-alternator applications.
The Monster-Ram® is built to eliminate the failure-prone factory grid heater by replacing it with a Banks high-flow intake plate and coil heater — removing the source of a well-documented factory failure point while improving airflow, throttle response, and fuel economy. It is the only 50-state emissions-compliant RAM intake elbow on the market.
Key Features
- Eliminates Factory Grid Heater Failure Risk: Replaces the OEM grid heater — a documented source of engine damage — with a Banks high-flow intake plate.
- Improved Airflow: Outflows the stock intake elbow by over 88.3%.
- Quicker Throttle Response: Reduced intake restriction improves engine responsiveness.
- Improved Fuel Efficiency: Optimized air pressure and distribution support better economy.
- Raises Boost Without Added Backpressure: Increases boost potential without raising turbine drive pressure.
- 50-State Emissions Compliant: CARB Executive Order D-161-170. Retains all factory emissions equipment.
- Triple Heat Capable: Includes a 750-watt Banks coil heater, with the option to upgrade to 2,250 watts.
- Stock Mounting Points: Accommodates factory mounting locations for a clean installation.
What’s Included
- Banks Monster-Ram® intake housing
- Banks high-flow cast intake plate
- Banks high-flow coil heater (750-watt)
- Proprietary #1 fuel line and installation hardware
- 3-3/8 inch inlet with four 1/8 inch NPT ports
Note: Available in Red, Black, or Natural Aluminum finishes.
Application Notes
This Monster-Ram® also fits dual-alternator equipped engines and retains all factory emissions equipment for full 50-state compliance. It does not fit Chassis Cab configurations — a separate Chassis Cab version is available for those applications.
Customers seeking additional cold-start heat can upgrade to 2,250 watts using the Banks Triple Heater Upgrade Kit, or add supplemental billet heaters for further cold-weather starting support.
Product Specifications
- Product Type: Intake Elbow with Grid Heater Delete
- Application: 2013–2018 Dodge Ram 2500 & Ram 3500 (Including Dual-Alternator Equipped Trucks)
- Engine: 6.7L Cummins Diesel
- Inlet Size: 3-3/8 Inch
- Ports: Four 1/8 Inch NPT
- Heater: Banks High-Flow Coil Heater, 750-Watt (Triple Heat Capable, Upgradeable to 2,250W)
- Airflow Improvement: Over 88.3% vs. Stock
- Emissions: Retains All Factory Emissions Equipment
- Fitment Restriction: Does Not Fit Chassis Cab
- SKU: 42798-PC
- Available Finishes: Red, Black, Natural Aluminum
Certifications
Emissions Status: 50-State Compliant — CARB Executive Order D-161-170.
Warranty
Covered under the Banks Limited Lifetime Warranty, which applies to every component in the Monster-Ram® kit, including the proprietary fuel line.
Installation Resources
- Download Owners Manual — Monster-Ram® Intake System with Fuel Line, 2013–2018 Dodge Ram 6.7L
- Download Heater and Billet Heater Upgrade Kit Wiring Diagrams
Estimated Install Time: 6 hours
California Proposition 65 Warning
WARNING: Cancer and Reproductive Harm — P65Warnings.ca.gov
Disclaimer
Verify fitment before ordering. This product is intended for compatible 2013–2018 Dodge Ram 6.7L Cummins applications, including dual-alternator equipped trucks, and does not fit Chassis Cab configurations. Warranty terms and installation requirements may vary by vehicle and location.
Vehicle Fitment
| Year | Make | Model | Engine |
|---|---|---|---|
| 2013 | Dodge/Ram | Ram 2500 / 3500 | 6.7L Cummins |
| 2014 | Dodge/Ram | Ram 2500 / 3500 | 6.7L Cummins |
| 2015 | Dodge/Ram | Ram 2500 / 3500 | 6.7L Cummins |
| 2016 | Dodge/Ram | Ram 2500 / 3500 | 6.7L Cummins |
| 2017 | Dodge/Ram | Ram 2500 / 3500 | 6.7L Cummins |
| 2018 | Dodge/Ram | Ram 2500 / 3500 | 6.7L Cummins |
Reviews
There are no reviews yet.